[Dune] AluCube grid in 2d?

[Andreas Dedner]

The error is correct at least with alu 1.23. There's a alu 1.5 on the 
way which includes cubes in 2d and surface grids 2d/3d - should be 
released within a week or two.

Andreas

On 24/11/11 16:13, Matteo Semplice wrote:
> Hi.
> Does the error reported below point to some mistake in my library
> setup/compilation or is it the intended behaviour (i.e. dune cannot
> handle ALUCube grid in 2d?)
>
> So, I downloaded ALUGrid-1.23 , configured it with
> ./configure --prefix=/home/matteo/
> --includedir=/home/matteo/include/alugrid
> and installed with "make all" and "make install". No errors were reported.
>
> Then I downloaded dune-common, grid, istl and grid-howto, and
> configured, compiled, installed with dunecontrol.opts
>
> PKG_CONFIG_PATH="/home/matteo/lib/pkgconfig"
> CONFIGURE_FLAGS="--enable-parallel
> --with-alugrid=/home/matteo/ALUGrid-1.23 --prefix=$HOME"
> (There is no newline in the definition of CONFIGURE_FLAGS in the actual
> file)
>
> Both the previously compiled alugrid libraries and the alberta libraries
> already in my system were found. Again, I noticed no errors.
>
> Then, I moved to the dune-grid-2.1.0 directory and tried to recompile
> adaptivefinitevolume with GRIDTYPE set to ALUGRID_SIMPLEX and
> ALUGRID_CONFORM, as suggested in the grid-howto. They compile and run
> correctly.
>
> Next I tried ALUGRID_CUBE and got the following error.
> I noticed that the error mentions dune/grid/alugrid/2d/alugrid.hh,
> dune/grid/alugrid.hh and lugrid/3d/capabilities.hh... is this ok?
>
> Thanks for any tip...
>
> Matteo
>
> ==========
> matteo at montebianco:~/dune2.1/dune-grid-howto-2.1.0$ make GRIDDIM=2
> GRIDTYPE=ALUGRID_CUBE adaptivefinitevolume
> g++ -std=c++0x -DHAVE_CONFIG_H -I.
> -I/home/matteo/dune2.1/dune-common-2.1.0
> -I/home/matteo/dune2.1/dune-grid-2.1.0
> -I/home/matteo/dune2.1/dune-istl-2.1.0 -I. -I/usr/include
> -I/usr/lib/openmpi/include -I/usr/lib/openmpi/include/openmpi -pthread
> -DMPIPP_H -DENABLE_MPI=1 -I/usr/include
> -I/home/matteo/dune2.1/dune-common-2.1.0
> -I/home/matteo/dune2.1/dune-grid-2.1.0
> -I/home/matteo/dune2.1/dune-istl-2.1.0 -I/usr/lib/openmpi/include
> -I/usr/lib/openmpi/include/openmpi -pthread -DMPIPP_H -DENABLE_MPI=1
> -I/home/matteo/dune2.1/dune-common-2.1.0 -DGRIDDIM=2 -DWORLDDIM=2
> -DALUGRID_CUBE -I/usr/include/alberta -DALBERTA_DIM=2 -DENABLE_ALBERTA
> -I/usr/lib/openmpi/include -I/usr/lib/openmpi/include/openmpi -pthread
> -DMPIPP_H -DENABLE_MPI=1 -I/home/matteo/include/alugrid
> -I/home/matteo/include/alugrid/serial
> -I/home/matteo/include/alugrid/duneinterface -DENABLE_ALUGRID
> -I/home/matteo/include/alugrid/parallel -I/usr/include -DENABLE_GMP=1
> -I/home/matteo/dune2.1/dune-grid-2.1.0 -I/usr/include/superlu
> -DENABLE_SUPERLU -I/home/matteo/dune2.1/dune-istl-2.1.0 -g -O2 -MT
> adaptivefinitevolume-adaptivefinitevolume.o -MD -MP -MF
> .deps/adaptivefinitevolume-adaptivefinitevolume.Tpo -c -o
> adaptivefinitevolume-adaptivefinitevolume.o `test -f
> 'adaptivefinitevolume.cc' || echo './'`adaptivefinitevolume.cc
> In file included from
> /home/matteo/dune2.1/dune-grid-2.1.0/dune/grid/alugrid/2d/alugrid.hh:8,
> from /home/matteo/dune2.1/dune-grid-2.1.0/dune/grid/alugrid.hh:11,
> from config.h:457,
> from adaptivefinitevolume.cc:1:
> /home/matteo/dune2.1/dune-grid-2.1.0/dune/grid/alugrid/2d/grid.hh: In
> instantiation of ‘Dune::ALU2dGrid<2, 2, (ALUGridSpace::ElementType)1u>’:
> /home/matteo/dune2.1/dune-grid-2.1.0/dune/grid/alugrid/3d/capabilities.hh:21:
> instantiated from ‘Dune::ALUCubeGrid<2, 2>’
> adaptivefinitevolume.cc:104: instantiated from here
> /home/matteo/dune2.1/dune-grid-2.1.0/dune/grid/alugrid/2d/grid.hh:192:
> error: static assertion failed: "ALU2dGrid only implemented for triangles."
> make: *** [adaptivefinitevolume-adaptivefinitevolume.o] Error 1
> ===============
>
> _______________________________________________
> Dune mailing list
> Dune at dune-project.org
> http://lists.dune-project.org/mailman/listinfo/dune